Walkthrough
The accreditation flow, one standard at a time
Follow Standard 4.2 from the first Quick Check to the assessor’s final status. Ten steps, three roles, one click each.
The walkthrough, step by step
- Accreditation Manager Lena Ortiz
- Review Manager Marcus Reyes
- Assessor Dana Okafor
-
Step 1 of 10 See what a policy covers
Lena Ortiz opens Policy 300: Use of Force in the Document Library and runs Quick Check. Badge 6 lists the standards in the manual that the policy supports, each with a match score.
The click: Quick Check With AI
The policy matches Standard 4.2 at 86%, with 3 of 4 units met. From the results she goes straight to Add Written Directive.
-
Step 2 of 10 Highlight the lines that prove each subpoint
She adds the policy as a written directive. AI highlights the sentences that meet each subpoint and tags them; she can edit any highlight or add her own before saving.
The click: Use AI to Highlight
Subpoints a, b and c are covered and d still needs proof. She saves with Add Written Directive, then attaches two proofs the same way with Add Proof.
-
Step 3 of 10 Send the standard for review
With the directive and proofs attached, she sends the standard to her agency’s Review Managers. Both tabs go at once.
The click: Send for review
Every item shows Under Review, and the tab notes who sent it and when.
The Review Managers get a bell notice, plus an email if they have turned emails on.
-
Step 4 of 10 Review each item
Marcus Reyes, a Review Manager, checks each highlight against its subpoint and sets the reviewer status. Not in Compliance would send the item back to Lena.
The click: Set In Compliance
The directive and both proofs are In Compliance.
Lena is notified of each change.
-
Step 5 of 10 Mark both tabs complete and sign the report
Once both tabs are marked Complete (Directives are Complete, Proofs are Complete), he signs the standard report. It carries the policy, proofs, highlights and notes, and every signature creates a new version.
The click: Sign
Version 1 is saved under Report Versions, as a PDF or an HTML file that opens offline.
-
Step 6 of 10 Check each item as the assessor
Northville PD’s manual is connected to the accrediting body, so Dana Okafor, the assigned assessor, can open the standard. She sees the agency’s statuses and highlights, read-only, and sets her own Assessor Status on each item. The 2024 analysis is out of date.
The click: Add to Plan
The Q1 reports are In Compliance and the 2024 analysis is Needs Revision, with a draft corrective action ready.
The agency’s Review Managers are notified of each status change.
-
Step 7 of 10 Share a corrective action plan
In the Corrective Actions tab she can write actions herself or ask for AI suggestions and add the ones she wants. When the plan is ready, she shares it with the agency.
The click: Share with Agency
The plan moves from Draft — Not Shared to Shared with Agency.
The agency’s Accreditation Manager, Review Manager and Agency Admin get a bell notice and an email with the plan.
-
Step 8 of 10 Fix it and tell the assessor
Lena uploads the 2025 analysis as a new proof, ticks Done on the action and leaves a comment for Dana.
The click: Notify Assessor of Updates
Dana will see the action marked Done, with Lena’s comment.
Dana gets a bell notice and an email with the plan.
-
Step 9 of 10 Accept the action
Dana checks the new proof and accepts the action. If more work were needed, Reopen Action would ask what is still missing.
The click: Accept Action
The action shows ✓ Accepted, and the agency sees an unread dot on the plan.
-
Step 10 of 10 Set the standard’s status
With every item checked, she sets the standard to In Compliance and closes the plan in the same step. A final status locks the standard.
The click: Set In Compliance
The standard is locked: evidence, statuses and item comments are read-only, and the standard’s chats stay open. Dana can still open the signed report under Report Versions.
The agency’s Accreditation Manager, Agency Admin and Review Manager are notified.
All 10 steps
- 1 See what a policy covers Accreditation Manager
- 2 Highlight the lines that prove each subpoint Accreditation Manager
- 3 Send the standard for review Accreditation Manager
- 4 Review each item Review Manager
- 5 Mark both tabs complete and sign the report Review Manager
- 6 Check each item as the assessor Assessor
- 7 Share a corrective action plan Assessor
- 8 Fix it and tell the assessor Accreditation Manager
- 9 Accept the action Assessor
- 10 Set the standard’s status Assessor
That’s the whole accreditation flow.
Sample agency and people. Screens are simplified; the button names and statuses are the ones in Badge 6.
Good to know
- Assessors see an agency’s evidence only on the manuals connected to their accrediting body, only when they’re assigned to that agency, and they can’t change it.
- Someone who is both Accreditation Manager and Review Manager doesn’t send for review: what they add goes straight to Under Review.
- To change anything after a final status, the assessor sets the standard back to In Progress, with a note.
- The assessor’s copy of the standard report leaves out the agency’s internal comments.
Other walkthroughs
-
Roles: Region ManagerAssessor
Final report
The region manager sets the template and assigns the report; the assessor fills it in; approval and the PDF.
7 steps
-
Roles: Policy AdminOfficerPolicy Review ManagerAttorney
Policies
Upload and redaction, publish, officer acknowledgment on a phone, then an edit through peer and attorney review.
8 steps
-
Roles: Region ManagerAssessorAccreditation Manager
Assessment visits
A visit window, assessors claiming their dates, and a locked schedule the agency can see.
5 steps
This Is Accreditation: Simplified. This Is Badge 6.
See Badge 6 with your own standards.
A 30-minute walkthrough with someone who knows accreditation. Bring a policy and we’ll show you what Badge 6 finds in it.